Buyhere22, 26 Somers Road, Rugby, CV22 7DH

830 tie point Solderless MB-102 Breadboard Power Supply Jumper Wires Starter Kit

£4.59 – £12.87

 

This kit contains the solderless breadboard, and optionally the power supply and jumper leads.

This high quality 830 tie-point Solderless Breadboard consists of 630 terminal strip tie-points connected vertically and 200 tie-point power rails at the top and bottom of the board connected horizontally.

With 126 separate vertical rows of 5 pins and 4 horizontal rows of 50 pin power rails, you can build complicated circuits with ease! The board has a standard 0.1″ pitch between pins so common through-hole devices such as transistors and integrated circuits connect easily.

Individual pins are identified by numbered rows and columns.

The holes accept wire or component legs between 20-29 AWG (0.3 – 0.8mm wire), and are rated to over 5000 insertions per point!

This ingenious Solderless Breadboard Power Supply slots into the power rails of a standard sized breadboard and can provide 5V and 3.3V power. This item is brand new and we have stock in the UK!

The output voltage is selected using jumpers for each voltage rail and can be turned on and off using the power switch on the board.

Power can be provided via the USB connector or via the DC power jack – the DC power jack accepts 6.5V to 12V. DO NOT EXCEED 12V ! DC Socket is centre pin positive.

Simply insert the Power Supply module into the breadboard, observing the polarity of supply + to + red line on breadboard and supply – to – blue line on breadboard.

This module produces clean, regulated 5V and 3.3V power that is ideal for prototyping use!

DC Current Output 700ma

IMPORTANT
PLEASE DO NOT EXCEED 12V INPUT WHICH MUST BE A REGULATED VOLTAGE, DO NOT USE AN UNREGULATED SUPPLY.
PLEASE CHECK YOUR INPUT VOLTAGE IS BETWEEN 6.5V
AND 12V WITH A VOLTMETER BEFORE APPLYING VOLTAGE TO THIS DEVICE.
EXCEEDING THIS VOLTAGE WILL DAMAGE THE ON-BOARD  REGULATORS AND WE WILL NOT BE ABLE TO REPLACE THE DEVICE.
PLEASE
ENSURE THAT THE OUTPUT IS 3.3V AND 5.0V BEFORE YOU CONNECT THIS
TO YOUR
DEVICE. WE CAN NOT BE HELD RESPONSIBLE FOR ANY DAMAGE WHICH MAYBE
CAUSED TO YOUR EQUIPMENT DUE TO IMPROPER USE OR PRIOR VOLTAGE CHECKS.

This item will be fully tested prior to despatch. Buy with confidence.

Approximately 65 solderless breadboard jumper leads Male to Male round pin of various lengths – ideal for use in prototyping projects on breadboards!

These leads are flexible, durable and easy to connect and disconnect – ideal for prototyping use!

The following lengths are provided:

  • 10cm – approximately 50x
  • 15cm – approximately 8x
  • 20cm – approximately 4x
  • 25cm – approximately 4x

Colours: Red, Orange, Yellow, Brown, Green, White, Blue, Black

 

 

 

Please read and note the following before ordering:
1) My Shipping is for UK Mainland ONLY. No Scotish Highland, Northern Ireland, Isle of Wight or other Isles. Some areas may incur additional costs, if you are unsure please contact me prior to ordering.
2) Please ensure you have a valid contact phone number, I may pass this number onto the Carrier for delivery. No refund for carriage cost will be offered, if delivery is delayed as a result of no valid contact number being provided.
3) I welcome collection for orders,please select collection on checkout otherwise your order will be despatched. Once your order has been picked and tested if applicable. We will then inform you of a date and time for collection. Please bring your payment card for verification when collecting your order. No order will be released without card verification.
4) I am unable to provide ANY technical support, please ensure you fully understand how this item works by checking for any datasheets (not provided with the item), to enable the product to be used within your application / project.
5) VERY IMPORTANT >> Do not make ANY permanent connections. Please test the item BEFORE making any permanent connections e.g. soldering to the item. Please ensure you have the means to test the item WITHOUT applying ANY solder to the item. If an item has any solder applied I will NOT accept any return.
6) When upgrading to 1st class post, (if the option is available), please note this is sent via Royal Mail and is not a guaranteed next day service. If you need a 48hr service please select 48hr delivery at extra cost. This will be sent via Royal Mail or courier. I do not offer a 24hr service. No weekend or public bank holiday deliveries.
7) We attempt to send out all orders received before 10.00am. This excludes weekends and public holidays.
8) Customers placing multiple orders. – I may ship all the orders as one, please do not ask for a refund of shipping cost after you have placed your orders. Please do not place your orders if you want a refund of shipping cost.
9) Some items may have a “Warranty Void if removed” sticker, please DO NOT tamper or remove these stickers. I will not accept any rertuns with tampered or removed sticker. Some buyers have tried to send back items that I have not supplied.

**** Important note **** Some sellers claim the stock is in the UK, please be careful, the seller is often in China and sends the item to a UK agent who then forwards the item on with a UK stamp. Check where the seller is located not just the item location. All my items are physically with me, here in the UK and I offer a quick delivery and communication within the UK.

During busy periods there maybe a delay in delivering your package by Royal Mail. I apologies in adavnce for any inconvenience but would like to point this out before you place your order.