Buyhere22, 26 Somers Road, Rugby, CV22 7DH

ESP8266 ESP-07 Remote Serial Port Transceiver WiFi and Adaptor Firmware v0.9.5.2

£7.99 – £11.99

 

ESP8266 ESP-07 With I/O Adaptor Board
Remote Serial Port WIFI Transceiver v0.9.5.2

UK STOCK, UK SELLER

The ESP8266 ESP-07 will come pre-solder mounted to the I/O adaptor board allowing pin pitch to 2.54mm breadboard friendly, You can select the option to have header pins supplied or not and if you would like the header pins pre-soldered, but remember the ESP-07 Module will come ready mounted and pre-soldered for you and FULLY TESTED !

The
ESP8266 is one of the most talked about modules on the internet. There
are so many applications this little unit can be put to, only limited by
your imagination.
ESP8266 is a highly integrated chip designed for the needs of a new
connected world. It offers a complete and self-contained Wi-Fi
networking solution, allowing it to either host the application or to
offload all Wi-Fi networking functions from another application
processor.

ESP8266 has powerful on-board processing and storage capabilities
that allow it to be integrated with the sensors and other application
specific devices through its GPIOs with minimal development up-front and
minimal loading during runtime. Its high degree of on-chip integration
allows for minimal external circuitry, and the entire solution,
including front-end module, is designed to occupy minimal PCB area.The ESP8266 is a highly integrated chip designed for the needs of a new
connected world. It offers a complete and self-contained Wi-Fi
networking solution, allowing it to either host the application or to
offload all Wi-Fi networking functions from another application
processor.The ESP8266 has powerful on-board processing and storage capabilities
that allow it to be integrated with the sensors and other application
specific devices through its GPIOs with minimal development up-front and
minimal loading during runtime. Its high degree of on-chip integration
allows for minimal external circuitry, and the entire solution,
including front-end module, is designed to occupy minimal PCB area.

 

Specification:

  • 802.11 b/g/n
  • 32-pin QFN package
  • Wi-Fi Direct (P2P), soft-AP
  • Integrated TCP/IP protocol stack
  • Integrated WEP, TKIP, AES, and WAPI engines
  • Integrated MAC/baseband processors
  • Integrated TR switch, balun, LNA, power amplifier and matching network
  • Integrated PLLs, regulators, DCXO and power management units
  • +19.5dBm output power in 802.11b mode
  • Power down leakage current of <10uA
  • Integrated RISC processor, on-chip memory and external memory interfaces
  • Integrated low power 32-bit CPU could be used as application processor
  • UART
  • Wake up and transmit packets in < 2ms
  • Standby power consumption of < 1.0mW (DTIM3)
  • VERY IMPORTANT THIS IS A 3.3V DEVICE

***************************************************************************************

Great NEWS

The ESP8266 ESP-07 that I provide will have firmware v0.9.5.2 AT Baud Rate 115200
When you send AT+GMR your ESP8266 ESP-07 device will respond with the version details as follows:
AT+GMR
AT version:0.21.0.0
SDK version:0.9.5
Please note that the SDK version displays 0.9.5 as apposed to 0.9.5.2
***************************************************************************************


The ESP8266 ESP-07 has the following pad outputs, Pitch distance is 2.54mm via the supplied I/O Adaptor Board.


 

Please also see my other ESP8266 devices as there are many types, offering different pin-out functions

THIS ITEM WILL BE FULLY TESTED PRIOR TO DESPATCHING (DO NOT EXCEED OPERATING
VOLTAGE), I will ensure that the firmware version is v0.9.5.2
I will check AT commands are responding and connect to a wireless router.
I will also connect Tx and Rx to a Microcontroller and test logging
onto a wireless router and transmit and receive data. I will therefore
not accept that the item has arrived as non-functioning.

I am unable to provide any technical support,
please ensure you fully understand how this item works by checking for
any datasheets (not provided with the item) , to enable the product
to be used within your application / project.

Please read and note the following before ordering:
1) My Shipping is for UK Mainland ONLY. No Scotish Highland, Northern Ireland, Isle of Wight or other Isles. Some areas may incur additional costs, if you are unsure please contact me prior to ordering.
2) Please ensure you have a valid contact phone number, I may pass this number onto the Carrier for delivery. No refund for carriage cost will be offered, if delivery is delayed as a result of no valid contact number being provided.
3) I welcome collection for orders,please select collection on checkout otherwise your order will be despatched. Once your order has been picked and tested if applicable. We will then inform you of a date and time for collection. Please bring your payment card for verification when collecting your order. No order will be released without card verification.
4) I am unable to provide ANY technical support, please ensure you fully understand how this item works by checking for any datasheets (not provided with the item), to enable the product to be used within your application / project.
5) VERY IMPORTANT >> Do not make ANY permanent connections. Please test the item BEFORE making any permanent connections e.g. soldering to the item. Please ensure you have the means to test the item WITHOUT applying ANY solder to the item. If an item has any solder applied I will NOT accept any return.

6) When upgrading to 1st class post, (if the option is available), please note this is sent via Royal Mail and is not a guaranteed next day service. If you need a 48hr service please select 48hr delivery at extra cost. This will be sent via Royal Mail or courier. I do not offer a 24hr service. No weekend or public bank holiday deliveries.
7) We attempt to send out all orders received before 10.00am. This excludes weekends and public holidays.

8) Customers placing multiple orders. – I may ship all the orders as one, please do not ask for a refund of shipping cost after you have placed your orders. Please do not place your orders if you want a refund of shipping cost.
9) Some items may have a “Warranty Void if removed” sticker, please DO NOT tamper or remove these stickers. I will not accept any rertuns with tampered or removed sticker. Some buyers have tried to send back items that I have not supplied.

**** Important note **** Some sellers claim the stock is in the UK, please be careful, the seller is often in China and sends the item to a UK agent who then forwards the item on with a UK stamp. Check where the seller is located not just the item location. All my items are physically with me, here in the UK and I offer a quick delivery and communication within the UK.

During busy periods there maybe a delay in delivering your package by Royal Mail. I apologies in adavnce for any inconvenience but would like to point this out before you place your order.